pic

OUR PRODUCT RANGE

 

permalogo

PERMA ANCHOR FIX-80

icon

HIGH STRENGTH THIXOTROPIC THREE COMPONENT POLYESTER GROUT

permaseal

DESCRIPTION

Perma Anchor Fix – 80 is a polyester resin based grout which is used in locations where very high early and ultimate strengths are required along with chemical resistance properties. The product is supplied in pre- measured three component units of base, reactor & initiator.

PRIMARY USES

  • Perma Anchor Fix- 80 is used for installation of dowel bars in concrete and for providing starter bars in RCC structures for continuation of structural concrete or in extension of structural members.
  • Perma Anchor Fix-80 can be used for fixing foundation bolts, base plates and rail tracks.
  • Because of its thixotropic nature the product is successfully used in vertical horizontal as well as in over-head applications.

DIRECTIONS FOR USE

  • Drill the holes for anchor with hammer drills so that holes with rough internal surface are obtained.
  • Clean the holes to be grouted with compressed air so that the holes are free from any loose ground material, which could affect the bond of the surface with the grout. Mix the base liquid with the initiator to a homogenous mix. There after add filler powder to the mix to make a smooth consistency paste. Fill the hole with this paste taking care to see that the hole is filled effectively from the bottom to avoid any entrapped air in the hole. Insert the dowel rod, anchor or bolt in the filled hole and hold it in position till it has become firm. Tool the mouth of the hole to make an even and smooth surface.

PROPERTIES

Product : Three Component
Base & Initiator : Straw Colored resinous liquid / initiator liquid
Powder (filler) : Free flowing white powder.
Flash Point Of The Liquid : 29°C
Application Temperature : 5°C to 40°C
Service Temperature : -20°C to 60°C

GEL TIME

Ambient Temperature ° C Gel Time Mins Min Time before loading in Hrs.
20 15 7
30 5 4
40 3 3
     

COMPRESSIVE STRENGTH

In 4 Hours : 20 N/ mm²
In 24 Hours : 50 N/ mm²
After 7 days : 90 N/ mm²
Tensile Strength : 30 N/ mm²

COVERAGE

Perma Anchor Fix-80 gives a paste of density 2.20. Hence one kg Perma Anchor Fix-80 gives a paste of 455 CC volume. The quantity of Perma Anchor Fix-80 required for anchoring various diameter bars in various diameter holes is as follows:

Qty Of Perma Anchor Fix- 80 Required In Gms For 100 Mm Bond.

Bolt Dia 12mm 16mm 20mm 25mm 32mm 40mm
Hole Dia
20 mm 44 25
25 mm 83 64 39
32 mm 152 133 108 69
40 mm 232 208 169 100
50 mm 363 324 255 156
             

NOTE : For effective anchoring the hole diameter should be at least 4 mm more than the anchor diameter and should not be more than 25 mm of the anchor diameter.

CHEMICAL RESISTANCE

Cured Perma Anchor Fix-80 is resistant to fresh and saline water, Petrol, diesel, oil, grease and most solvents, acids and alkalies.

ANCHOR DESIGN

Perma Anchor Fix-80 is capable of holding heavy loads but the failure occurs in concrete, brick work, rock etc., in which the anchorage is provided. However loads which Perma Anchor Fix-80 withstands in sound concrete with 16 mm anchor in 20 mm dia hole are as follows :

Embedded Length Failure Load Tonnes
100 3.5
200 8.5
400 18.0
600 30.0
   

NOTE: A Minimum factor of safety of 2 should be considered in all anchoring designs. Strength of the body in which the anchoring is provided should always be the guiding factor in anchor design. Above 60°C the Anchor Fix-80 starts softening. Hence Anchor Fix-80 should not be utilized in places where temperatures are expected to rise over 60°C.

EQUIPMENT CARE

All equipment must be cleaned immediately after use with cleaning solvents. Similar procedures should be adopted for break periods.

HEALTH AND SAFETY

Perma Anchor Fix-80 should be handled carefully. Use of Mask and hand gloves recommended. Avoid the contact of the product with the skin. Work in a well ventilated area. The product being flammable, should be kept away from flame and smoking in vicinity of application area should be prohibited.

PACKING

Perma Anchor Fix-80 is available in 250 gms and 1 kg packing apart from bulk on special request.

SHELF LIFE

Perma Anchor Fix-80 has a self life of 6 Months from the date of manufacture if stored in original packing.

DISCLAIMER

PERMA warrants that all products are free from any defects of manufacture and comply with the specifications given in their respective technical data sheet. No warranty can be given as to the results of use because conditions of use, such as site conditions, surface preparations, workmanship, weather, structural issues and other factors are beyond the control of PERMA. Purchaser agrees to seek the advice of qualified professionals to carry out tests & take trials to determine the suitability of products for their intended purpose prior to full scale usage of PERMA products and assumes all risks.

The company does not assume any liability for unsatisfactory results, arising from the use of our products. Purchaser’s sole liability is limited to replacement of product or refund of the purchase price paid if any product proven defective. No other warranties, express or implied, shall apply including any warranty of merchantability or fitness for a particular purpose. PERMA shall not be liable for any consequential damages arising from the use of our products for unsatisfactory results.

The information supplied in this datasheet is based on our experience through extensive research and is given in good faith in order to help prospective users. We reserve the right to update the information provided in our technical data sheet at any time without prior notice within the scope of technical progress or new developments.


Click the below Button to print the current page.

 
Contact Us
X

Contact Form